Medical Grade Epoxy Offers Thermal Conductivity and Electrical Insulation
Master Bond EP42HT-4AOMed Black is a two part epoxy created for medical device manufacturing. It is biocompatible and non-cytotoxic, passing both USP Class VI and ISO 10993-5 certifications.
This epoxy withstands aggressive chemical sterilants, radiation and repeated cycles of autoclaving. EP42HT-4AOMed Black offers both cryogenic serviceability and heat resistance with a service temperature range from 4K to 400°F. Its thermal conductivity measures 9-10 BTU•in/(ft2•hr•°F) ...
This epoxy withstands aggressive chemical sterilants, radiation and repeated cycles of autoclaving. EP42HT-4AOMed Black offers both cryogenic serviceability and heat resistance with a service temperature range from 4K to 400°F. Its thermal conductivity measures 9-10 BTU•in/(ft2•hr•°F) and its volume resistivity is greater than 1014 ohm-cm. The system contains a filler, which contributes to its high strength profile and dimensional stability. This adhesive bonds well to metals, composites, glass, ceramics, rubbers and plastics and features a tensile modulus of 500,000-550,000 psi, a compressive strength of 24,000-26,000 psi, and a tensile strength of 7,000-8,000 psi.
This epoxy can cure at room temperature, yet faster cures can be achieved by heat curing. In order to obtain optimal properties, an overnight cure at room temperature, followed by heat curing at 150-200°F for 2-3 hours is recommended. The mix ratio is 100 to 40 by weight. Once mixed, this versatile adhesive has very good flow properties, making it suitable for bonding, sealing and coating applications. Upon curing, EP42HT-4AOMed Black exhibits very low shrinkage, low exotherm and can be used for castings up to 2-3 inches thick. This opaque black epoxy is available in the following size kits: ½ pint, pint, quart and gallon. It is also available in pre-mixed and frozen syringes, which are compatible with automated dispensing equipment.
Published by Master Bond Inc. on Feb 02, 2021
LED405Med: Biocompatible, Nanosilica Filled LED Curable Adhesive
Master Bond LED405Med is a one part, nanofilled system that cures quickly upon exposure to a 405 nm LED light. It does not require a UV light source. It meets ISO 10993-5 for cytotoxicity and resists sterilization. It can cure up to 1/8 think and has low shrinkage upon cure. It also features outstanding optic...
X21Med: Polyolefin Primer/Adhesive Meets ISO 10993-5 Requirements
Master Bond X21Med is a toughened one part system that can be used for bonding and priming polyolefinic surfaces. This exceptionally low viscosity (<250 cps) solvent based system is easy to apply and process. It cures at room temperature or more rapidly with the addition of heat. X21Med passes ISO 10993-5 ...
EP42HT-2Med: High Temperature Resistant Epoxy Withstands Multiple Sterilization Cycles
Capable of withstanding repeated cycles of autoclaving, radiation, EtO and cold sterilants, EP42HT-2Med is a room temperature curable, two part epoxy that complies with USP Class VI testing. It may be used as an adhesive, sealant, coating and casting material. It has excellent electrical insulation properties...
EP3HTMed: Chemically Resistant Polymer Meets USP Class VI Specifications
Master Bond EP3HTMed fully meets USP Class VI requirements and is formulated to cure at elevated temperatures. It has excellent resistance to radiation, EtO, autoclaving and chemical sterilants. EP3HTMed has a service operating temperature range of -60°F to +400°F [-51°C to +204°C], is 100% reactive and does ...
UV18Med: Medical Grade UV System Meets USP Class VI Specifications
USP Class VI certified UV18Med is a special UV system for bonding, coating and sealing featuring superb chemical resistance, excellent physical strength properties and toughness. It cures readily in 20-30 seconds when exposed to a UV light emitting at a wavelength of 320-365 nm. It is ideal for high productio...
MasterSil 912Med: Biocompatible Silicone Passes USP Class VI Testing
MasterSil 912Med is a single component silicone with a paste viscosity for bonding, sealing and coating medical devices. This non-corrosive, neutral cure compound complies with USP Class VI and ISO 10993-5 specifications. It resists many kinds of sterilization including gamma radiation, EtO and some types of ...
LED403Med: LED Curable System Meets USP Class VI Specifications
One part LED403Med cures in thin sections in 15-30 seconds upon exposure to a 405 nm wavelength LED light. Featuring excellent optical clarity and light transmission properties, it fully cures tack-free without any oxygen inhibition. This dimensionally stable system resists various sterilization methods inclu...